Automotive Water Treatment and Paint Shop Water
Low-conductivity water for pretreatment, electrocoat and final rinse lines, with cooling tower water and rinse water recovery.
In an automotive or supplier plant the most sensitive use of water is in the paint shop. Bodies and parts pass through successive baths such as degreasing, phosphating or thin-film coating, and electrocoat; rinsing takes place between and after the baths. Ions left in the rinse water contaminate the next bath and, trapped under the paint, can lead to staining, blistering and reduced corrosion resistance. The decisive parameter is therefore low conductivity.
The same plant also uses water in cooling towers, compressors and welding and press lines, and the expectations of these lines differ from the paint shop. Rather than supplying one quality everywhere, a reverse osmosis based pure water line for the paint shop and a separate arrangement that controls scaling and biological growth on the cooling side is more balanced. We start with a raw water analysis and an on-site review of the lines.
The decisive quality
Pretreatment rinses
The rinses between degreasing and phosphating or thin-film coating baths prevent the chemistry of one bath from being carried into the next. Conductivity and hardness are decisive; the final rinse before electrocoat is done with low-conductivity water.
Electrocoat bath
The balance of the electrocoat bath is sensitive to foreign ions entering it; hardness and chloride directly affect coating quality and bath stability. Low-conductivity water is used for bath make-up and top-up and for the subsequent rinses; the permeate separated from the bath by ultrafiltration is also used in the rinse circuit.
Final rinse and spray booth
A water droplet drying on the surface before painting leaves its salts behind. Low conductivity is therefore decisive in the final rinse. For air humidification in spray booths, treated water is also preferred to prevent nozzle clogging and mineral dust settling on surfaces.
Cooling towers
Welding robots, compressors, moulds and press lines require cooling water. Control of scaling, corrosion and biological growth is decisive here; the hardness and suspended solids load of the make-up water directly affect the efficiency of the tower.
Systems that matter in this sector
Reverse Osmosis Systems
Produces low-conductivity water for pretreatment, electrocoat and final rinse lines. On lines that require even lower conductivity, an EDI or mixed bed polishing stage can be added behind it.
View system →Electrodeionization (EDI) Systems
For final rinse and electrocoat top-up water, continuously brings the reverse osmosis permeate to lower conductivity without chemical regeneration; it removes the need to store acid and caustic on site.
View system →Ultrafiltration (UF) Systems
Retains emulsified oil, suspended solids and metal hydroxides in degreasing and rinse water; it forms the pre-stage for reusing these streams with reverse osmosis.
View system →Cooling Water Treatment
Removes the sediment that collects in the cooling tower basin with side-stream filtration; it limits fouling and efficiency loss in the heat exchangers of welding and press lines. Clean circulating water also helps the chemical conditioning programme work more effectively.
View system →Water Recovery Plants
Makes the suitable paint shop rinse streams and cooling tower blowdown reusable again; the volumes of purchased water and of discharged waste water fall together.
View system →
Work out your line in a few steps
The solution finder opens with this sector selected; choose your water source and goal and it shows the treatment stages that fit.
Frequently asked questions
Why is pure water used in an automotive paint shop?
Rinse water dries on the surface of the part and leaves its salts behind. When paint is applied over these salts, blistering, staining and reduced corrosion resistance can appear over time. Ions carried over in the rinse water also upset the chemistry of the next bath. That is why low-conductivity water is used especially before electrocoat and in the final rinse; the target value is usually set by the process instructions of the chemical and paint supplier.
Is reverse osmosis enough for an electrocoat line?
On most lines reverse osmosis permeate is sufficient for bath top-up and rinsing. If the process instructions call for lower conductivity, or the raw water salinity is high, an EDI or mixed bed polishing stage is added after the reverse osmosis. Which arrangement is needed is determined jointly by the raw water analysis and the quality the process supplier requires.
Can paint shop rinse water be recovered?
Often yes, depending on the content of the stream. Counter-flow cascade rinsing reduces consumption from the outset; the remaining streams can be made reusable with ultrafiltration and reverse osmosis. Streams high in oil, paint residue and metals are assessed separately. We first determine the profile of the streams, then decide together which of them can be recovered technically and economically.
Sectors with similar needs
Water Treatment for the Paper and Packaging Industry
Water quality for stock preparation, the paper machine and the steam line; filtration and recovery of the white water that circulates.
View →Water Treatment and Softening for Hotels and Hospitals
A treatment arrangement for drinking and utility water, the hot water line and heating–cooling circuits, and for equipment feedwater in healthcare facilities.
View →Water Treatment for the Food and Beverage Industry
Industrial water treatment arrangements that meet the different quality requirements of product water, line cleaning, steam and cooling separately.
View →
Send us your raw water analysis and the flow rate you need
Let us size the system together; we will survey the site in person if needed.

