Skip to content
Sectors

Water Treatment for Metalworking and Surface Finishing

Solutions that supply stable, low-conductivity water to rinsing, bath make-up and cutting fluid lines, and plan for the recovery of rinse water.

On surface treatment lines water does two main jobs: making up the baths and rinsing the part between them. At every step, from degreasing, pickling and phosphating to electroplating, anodising and pretreatment before painting, the part has to enter the next bath with a clean surface. Chloride, sulphate and hardness ions left in the rinse water leave marks on the drying surface, weaken the adhesion of paint and coatings, and are carried into the next bath, upsetting its chemistry.

That is why the target in the final rinse is usually low conductivity, while intermediate rinses can be fed with lower-quality water in a counterflow cascade arrangement. In machining, the water used to prepare cutting fluids and the cooling circuits of induction, welding and quenching lines also carry their own quality requirements. We start with a raw water analysis and an on-site inspection of the line, decide which water goes to which point, and then select the stages.

Where water is used

The decisive quality

  • Final rinse

    The final rinse before plating, anodising or painting is the step that determines what stays on the part surface. Conductivity is decisive here: ions left on the surface after drying cause spots, and under paint they draw in moisture, setting the stage for blistering and corrosion.

  • Bath make-up and top-up

    The water used to make up plating, phosphating and anodising baths, and the top-up water that replaces evaporation losses, become part of the bath chemistry. Hardness forms precipitates in the bath, while ions such as chloride accumulate, alter coating quality and shorten bath life; conductivity and ionic composition are decisive.

  • Cutting fluid preparation

    Water-based cutting and grinding fluids used in machining consist largely of water. Hardness destabilises the emulsion and leaves deposits in the machine; chloride and sulphate accelerate corrosion on the part and the machine tool. That is why softened or desalinated water is used to prepare the emulsion, as recommended by the fluid manufacturer.

  • Cooling circuits

    Induction furnaces, welding machines, quenching lines and hydraulic units need cooling water. In closed circuits, especially in induction systems, low-conductivity water limits both scaling and the risk of electrical leakage; in open tower circuits, scale, corrosion and biological growth are controlled.

Work out your line in a few steps

The solution finder opens with this sector selected; choose your water source and goal and it shows the treatment stages that fit.

Try the solution finder →

Frequently asked questions

Why must rinse water on a plating line have low conductivity?

Conductivity is an indicator of the dissolved salts in the water. As the part dries after the final rinse, these salts stay on the surface; they leave spots and marks and, under paint or a coating, can draw in moisture and lead to blistering and corrosion. In intermediate rinses, the water carried over with the part upsets the chemistry of the next bath. The target value is set by the coating process and the chemical supplier’s recommendation.

Can rinse water on a surface treatment line be recovered?

In most cases, yes; rinse waters are dilute compared with the baths, so treating them is relatively easy. The stream is treated by filtration and reverse osmosis or by ion exchange columns and returned to rinsing. Rinses from baths with different chemistries are collected separately where necessary; the concentrate and regeneration waste are routed to the existing waste water treatment plant. Feasibility becomes clear once the streams have been characterised.

Reverse osmosis or demineralisation for surface treatment?

The two often work together. Reverse osmosis removes most dissolved salts using electrical energy and without regeneration chemicals; ion exchange resins reach higher purity but need regeneration with acid and caustic. The common arrangement is one in which reverse osmosis takes the main load and a mixed bed polishes only for the points that need high purity. The choice depends on the target quality, the flow and chemical handling.

Send us your raw water analysis and the flow rate you need

Let us size the system together; we will survey the site in person if needed.